Kenwood Car Video System LZ 612IR User Manual

LZ-612IR  
WIDE TOUCH SCREEN MONITOR  
INSTRUCTION MANUAL  
MONITEUR ECRAN LARGE TACTILE  
MODE D’EMPLOI  
BREITBILD-BERÜHRUNGSBILDSCHIRM  
BEDIENUNGSANLEITUNG  
BREEDBEELD MONITOR MET AANRAAKSCHERM  
GEBRUIKSAANWIJZING  
MONITOR TOUCH SCREEN PANORAMICO  
ISTRUZIONI PER L’USO  
MONITOR DE PANTALLA TÁCTIL PANORÁMICA  
MANUAL DE INSTRUCCIONES  
MONITOR DE ECRÃ LARGO DE TOQUE  
MANUAL DE INSTRUÇÕES  
ШИРОКОФОРМАТНЫЙ МОНИТОР С СЕНСОРНЫМ ЭКРАНОМ  
ИHCTPУKЦИЯ ПO ЭKCПЛУATAЦИИ  
触摸宽屏显示器  
使用说明书  
Take the time to read through this instruction manual.  
Familiarity with installation and operation procedures will help you obtain the best  
performance from your new monitor.  
For your records  
Record the serial number, found on the back of the unit, in the spaces designated on the  
warranty card, and in the space provided below. Refer to the model and serial numbers  
whenever you call upon your Kenwood dealer for information or service on the product.  
Model LZ-612IR Serial number  
US Residents Only  
Register Online  
Register your Kenwood product at  
© B64-4655-08/00 (W)  
 
This Product is not installed by the manufacturer of a  
vehicle on the production line, nor by the professional  
importer of a vehicle into an EU Member State.  
DVD player units you can control from the  
LZ-612IR (As of September, 2009):  
KDV-S211P, KDV-S221P, KDV-S250P, KDV-S240P,  
KDV-S230P, KDV-S220P, KDV-S210P  
Information on Disposal of Old Electrical  
and Electronic Equipment and Batteries  
(applicable for EU countries that have  
adopted separate waste collection systems)  
Products and batteries with the symbol  
(crossed-out wheeled bin) cannot be  
disposed as household waste.  
IR Wireless Headphone  
You can use IR wireless Head Phone as follows;  
KHP-IR72  
Old electrical and electronic equipment  
and batteries should be recycled at a facility  
capable of handling these items and their  
waste byproducts.  
Contact your local authority for details in  
locating a recycle facility nearest to you.  
Proper recycling and waste disposal will  
help conserve resources whilst preventing  
detrimental effects on our health and the  
environment.  
Notice: The sign “Pbbelow the symbol for  
batteries indicates that this battery  
contains lead.  
Declaration of Conformity with regard to  
the EMC Directive 2004/108/EC  
Manufacturer:  
Kenwood Corporation  
2967-3 Ishikawa-machi, Hachioji-shi, Tokyo, 192-8525 Japan  
EU Representative’s:  
Kenwood Electronics Europe BV  
Amsterdamseweg 37, 1422 AC UITHOORN, The Netherlands  
FCC WARNING  
This equipment may generate or use radio  
frequency energy. Changes or modifications to this  
equipment may cause harmful interference unless  
the modifications are expressly approved in the  
instruction manual. The user could lose the authority  
to operate this equipment if an unauthorized change  
or modification is made.  
NOTE  
This symbol mark indicates that  
Kenwood manufactured this product  
so as to decrease harmful influence on  
the environment.  
This Class B digital apparatus complies with Canadian  
ICES-003.  
English  
|
3
 
Basic Operation  
IR transmitter LED  
Remote control sensor  
(For DVD remote only)  
Turning Monitor ON/OFF  
Turning ON the Power  
Press the [ ] button.  
Turning OFF the Power  
Press the [ ] button.  
Video Source Selection  
1 Enter Select screen mode  
Touch the display window.  
2 Select the AV input source  
Touch the [AV IN] button.  
MENU
When button is pressed, the video source switches  
as follows:  
Display  
AV1  
AV2  
Setting  
Select the AV1 input source.  
Select the AV2 input (DVD input) source.  
|
4
LZ-612IR  
 
LZ-612IR with Kenwood DVD Player (Optional Accessory)  
DVD Player Operation  
DVD Player Control  
DVD Player Setup  
1 Enter Select screen mode  
1 Enter Select screen mode  
Touch the display window.  
Touch the display window.  
2 Select the function  
2 Select the function  
Touch the function button.  
Touch the function button.  
MENU  
TOP  
AUD  
SUBT  
PAGE  
PAGE  
SET  
REP  
AV IN  
RTN  
ENT  
Display  
PAGE  
MENU  
Function  
Display  
PAGE  
AUD  
Function  
Move to the DVD Player Control screen.  
Change the audio language.  
Move to the DVD Player Setup screen.  
Move to Monitor Setting screen. (page 6)  
Press to switch sequentially between playback and  
pause.  
SUBT  
Change the subtitle language.  
///Move to select a menu on the DVD menu.  
Press to stop playback.  
TOP  
SET  
RTN  
ENT  
Return to the top menu.  
Display the DVD menu.  
Moves to the previous menu.  
Performs the selected function.  
Search for a next chapter, scene or track.  
Search for a previous chapter, scene or track.  
Press to perform fast forwards.  
Press to perform fast backwards.  
Use when repeating a specific title or a track on the DVD  
player. (Chapter, Title, File, Folder, Track, One All)  
3 Exit DVD Player Setup mode  
REP  
Touch the screen except function button.  
AV IN  
Change AV1/ AV2 input source.  
• The relevant OSD is displayed only when the DVD  
Control in <Other Setting> (page 7) is turned on.  
• You can operate the Kenwood DVD player connected to  
the Hideaway box when the DVD Control is turned on.  
3 Exit DVD Player Control mode  
Touch the screen except function button.  
• The relevant OSD is displayed only when the DVD  
Control in <Other Setting> (page 7) is turned on.  
• You can operate the Kenwood DVD player connected to  
the Hideaway box when the DVD Control is turned on.  
English  
|
5
 
Monitor Setting  
Picture Quality Setting  
Screen Setting  
You can adjust the picture quality of the monitor.  
Change the menu OSD language and monitor  
screen size.  
1 Enter Select screen mode  
Touch the display window.  
1 Enter Select screen mode  
Touch the display window.  
2 Select the MENU function  
Touch the [MENU] button.  
2 Select the MENU function  
Touch the [MENU] button.  
3 Select the Picture Quality Setting mode  
Touch the [  
] button.  
3 Select the Screen Setting mode  
Touch the [  
] button.  
4 Select the adjusting item  
Touch the item.  
4 Select the adjusting item  
Touch the item.  
Brightness  
Contrast  
Color  
50  
50  
50  
Language  
Mode  
English  
Full  
Tint  
50  
5
Sharpness  
5 Adjusting the item  
Touch the [] or [] button.  
5 Adjusting the item  
Touch the [] or [] button.  
Item  
Setting  
Item  
Language  
Setting  
Brightness  
[] Stronger contrast [] Less contrast  
"0" "50" "100"  
Change MENU OSD Language.  
"English"/"Français"/"Deutsch"/"Español"  
"Full"  
Full picture mode.  
Contrast  
Color  
[] Less contrast  
"0" "50" "100"  
[] Weaker intensity  
"0" "50" "100"  
[] Purplish skin tones  
"0" "50" "100"  
[] Softer definition  
"0" "5" "10"  
[] More contrast  
Mode  
[] Stronger intensity  
[] Greenish skin tones  
[] Crisper definition  
Tint  
”Just”  
Justify picture mode.  
Sharpness  
“Zoom”  
Zoom picture mode.  
(Factory setting: Underlined)  
6 Exit Picture Quality setting mode  
Touch the [ ] button.  
"Normal"  
Normal picture mode.  
• The “Tintcan be adjusted when NTSC video signal is  
input.  
• If you make no operation for 10 seconds, monitor setting  
mode is automatically canceled.  
(Factory setting: Underlined)  
6 Exit Screen Setting mode  
Touch the [  
] button.  
|
6
LZ-612IR  
 
Other Setting  
Change the other settings.  
1 Enter Select screen mode  
Touch the display window.  
2 Select the MENU function  
Touch the [MENU] button.  
3 Select the Other Setting mode  
Touch the [  
] button.  
4 Select the adjusting item  
Touch the item.  
DVD/TV Control  
Audio  
Off  
1-ch  
Initialize  
5 Adjusting the item  
Touch the [] or [] button.  
Item  
Setting  
DVD/TV Control  
Set DVD/TV Player Control/Setup OSD ON or OFF  
in AV2 input source.  
"Off"/"DVD"/"TV" [”TV”no use.]  
Audio  
Displays the IR Headphones transmitter  
frequency.  
"1-ch": 2.3 MHz/"2-ch": 3.2 MHz  
Initialize  
The setting value is set to the initial state of  
factory.  
(Factory setting: Underlined)  
6 Exit Other Setting mode  
Touch the [  
] button.  
Refer to the instruction manual of IR Headphones  
(optional accessory), when setting for frequency.  
English  
|
7
 
Accesaries/Installation Procedure  
Accessories  
Installation Procedure  
1. To prevent short circuits, remove the key from the  
ignition and disconnect the terminal of the  
battery.  
2. Make the proper input and output cable  
connections for each unit.  
3. Connect the wiring harness wires in the following  
order: ground, ignition.  
4. Connect the wiring harness connector to the unit.  
5. Install the unit in your car.  
6. Reconnect the terminal of the battery.  
7. Press the reset button. (page 2)  
DC Cord ..........1  
Monitor Cable ..........2  
WARNING  
• This product is intended for use with 12V DC negative  
ground power only. Do not connect it to any other power  
supply.  
RCA Cable ..........2  
• To prevent shorting, disconnect the battery cable from the  
negative terminal of the battery during installation.  
• Be sure to firmly stabilise this product. Do not install it in a  
location which is not stable.  
• Follow the installation and wiring procedures described in  
this manual. Improper wiring or modified installation can  
not only result in malfunction or damage to the unit but  
may also result in an accident.  
Remote Control Cable ..........1  
Template ..........1  
• Mounting and wiring this product requires skills and  
experience. For safety's sake, leave the mounting and wiring  
work to professionals.  
• If your car’s ignition does not come with an ACC position,  
connect the ignition wires to a power source that can be  
turned on and off with the ignition key. If you connect the  
ignition wire to a power source that receives a constant  
voltage supply, as with battery wires, the battery may die.  
• If the fuse blows, first make sure that the wires have not  
caused a short circuit, then replace the old fuse with one  
with the same rating.  
• Do not let unconnected wires or terminals touch metal  
on the car or anything else conducting electricity. To  
prevent short circuits do not remove the caps from unused  
terminals or from the ends of the unconnected wires.  
• After the unit is installed, check whether the brake lamps,  
blinkers, wipers, etc. on the car are working properly.  
• Insulate unconnected wires with vinyl tape or other similar  
material.  
Mounting Bracket ..........2  
Removal Tool ..........1  
Mounting Screw (Ø4x16) ..........2  
• Thoroughly wipe away oil and other dirt from the  
installation surface.  
Please avoid installation on uneven surfaces.  
• Do not install the Hideaway Unit under the carpet.  
Otherwise heat build-up occurs and the unit may be  
damaged.  
|
8
LZ-612IR  
 
Connection  
Monitor Unit  
Monitor Unit  
Monitor Cable  
(Accessory)  
Hideaway Unit  
AV1 INPUT  
AV OUTPUT  
• Visual input (Yellow)  
(AV2 input signal only)  
• Audio left input (White)  
• Audio right input (Red)  
• Visual output (Yellow)  
• Audio left output (White)  
• Audio right output (Red)  
DC Cord  
(Accessory)  
AV2 INPUT (DVD Player)  
• Visual input (Yellow)  
• Audio left input (White)  
• Audio right input (Red)  
Remote Control Cable  
(Accessory)  
• If you are using this unit with a  
compatible Kenwood DVD player,  
connecting the Remote Control Cable  
will allow the LZ-612IR’s remote to  
control Kenwood DVD player as well as  
the monitor.  
RCA Cable  
(Accessory)  
To Audio/Visual Output  
To Remote Control Sensor input  
Kenwood DVD Player  
(Optional Accessory)  
Ignition key switch  
ACC  
Fuse (5A)  
Ignition cable (Red)  
Car fuse box  
(Main fuse)  
Ground cable (Black) (To car chassis)  
Battery  
 
English  
|
9
Installation  
Installation for Monitor Unit  
Before mounting the monitor to the headrest:  
Perform the required external connections first (Accessory ).  
Using the supplied paper template (Accessory ), mark the area to be cut out of the headrest, then carefully  
cut it.  
1 Connect Monitor and monitor connection cord (Accessory ).  
2 Install the monitor unit in the bracket (Accessory ).  
Headrest  
Installation plate (not supplied)  
Mounting Bracket  
(Accessory)  
Monitor Unit  
Screws  
(not supplied)  
Template  
(Accessory)  
Monitor Cable  
(Accessory)  
Installation for Hideaway Unit  
Removing the Monitor Unit  
Use screws (Accessory ) to fix Hideaway Unit onto  
an audio board or another.  
1 Insert the removal tool (Accessory ) deeply into  
the slots on TOP side, as shown.  
Accessory ⑧  
Accessory ⑦  
2 Pull the monitor unit all the way out with your  
hands, being careful not to drop it.  
|
10  
LZ-612IR  
 
Troubleshooting Guide  
Specifications  
What might seem to be a malfunction in your unit  
may just be the result of slight miss operation or  
miss wiring. Before calling service, first check the  
Monitor Unit  
Screen size  
: 6.1 inches wide  
136.1 (W) × 72.0 (H) × 154.0 (Diagonal) mm  
5-6/16 (W) × 2-13/16 (H) inches  
following table for possible problems.  
Display system  
: Transparent TN LCD panel  
Drive system  
: TFT active matrix system  
Number of pixels  
: 336,960 pixels (480 H × 234 V × RGB)  
The power does not turn on.  
! The fuse has blown.  
After checking for short circuits in the wires,  
replace the fuse with one having the same  
rating.  
Effective pixels  
: 99.99 %  
Pixel arrangement  
! No ACC position on vehicle ignition.  
Connect the same wire to the ignition as the  
battery wire.  
: RGB striped arrangement  
Back lighting  
: LED  
Nothing happens when the buttons are pressed.  
!
The computer chip in the unit is not functioning  
normally.  
IR Transmitter Output  
: (1-ch) L ch: 2.3 MHz/R ch: 2.8 MHz  
: (2-ch) L ch: 3.2 MHz/R ch: 3.8 MHz  
Press the reset button on the unit (page 2).  
The screen is dark.  
Hideaway Unit  
! The unit is in a location where temperature is low.  
If the temperature of the monitor unit drops, the  
screen may appear darker when power is first  
turned on due to the characteristics of a liquid  
crystal panel. Wait a while after turning power on  
for the temperature to rise. Normal brightness  
will return.  
Colour system  
: NTSC/PAL  
External video input level (RCA jacks)  
: 1 ± 0.1 Vp-p/75 Ω  
External audio input level (RCA jacks)  
: 2 V/10 KΩ  
Video output level (RCA jacks)  
: 1 ± 0.1 Vp-p/75 Ω  
Audio output level (RCA jacks)  
: 1.2 V/10 KΩ  
No sound from wireless headphones.  
! The frequency setting is not set correctly.  
Select the transmitter frequency according to  
your headphones.  
General  
! The headphones power is off.  
Operating voltage  
: 14.4 V DC (11 - 16 V)  
The headphones power switch is turned on.  
! The headphones batteries are exhausted.  
Replace the headphones batteries with fresh  
ones.  
Current consumption  
: 1.5 A  
Consumed Power  
: 14 W  
Operational temperature range  
: –10 °C to +60 °C  
Storage temperature range  
: –30 °C to +85 °C  
Dimensions (W × H × D)  
Monitor unit : 177 × 122 × 34 mm  
7 × 4-7/8 × 1-5/16 inch  
Hideaway unit : 141.5 × 88.5 × 32.5 mm  
5-9/16 × 3-8/16 × 1-4/16 inch  
Weight  
Monitor unit : 375 g (0.83 lbs)  
Hideaway unit : 145 g (0.32 lbs)  
Specifications subject to change without notice.  
Although the effective pixels for the liquid crystal panel is  
given as 99.99% or more, 0.01% of the pixels may not light  
or may light incorrectly.  
English  
|
11  
 

Infiniti Speaker System 9301297 001 User Manual
Infinity Vacuum Cleaner NV31C User Manual
InFocus Projector Accessories SP CEIL 004 User Manual
JVC Stereo System 0510WMKMDWJMM User Manual
Kenwood Stereo System DC 20 User Manual
Kettler Elliptical Trainer 07851 590 User Manual
Kingston Technology Computer Drive DT4000 User Manual
KitchenAid Cooktop KECC506RSS05 User Manual
Klipsch Speaker GMX D 51 User Manual
Konica Minolta Printer 1650EN User Manual